Relay protection testing solutions

The key partner to take assertive decisions over your protection network
See how it works
X
See how it works
Learn more

1 Hz testing.

One test makes a big difference

Las pruebas de factor de potencia/factor de disipación a 1 Hz proporcionan confianza en la evaluación del estado del aislamiento a 50/60 Hz. Con un instrumento y una conexión, la prueba proporciona una toma de decisiones inmediata y fiable para activos de alta tensión críticos.

¿Tienes alguna pregunta? Obtén la respuesta

Lorem ipsum dolor sit amet, consectetur adipiscing elit.

¿Tiene alguna duda sobre los resultados de las pruebas de factor de potencia/factor de disipación (PF/DF) de frecuencia de potencia (50 o 60 Hz) obtenidos de sus activos de AT?

Sobre el terreno, es habitual medir la PF/DF de frecuencia de potencia y obtener resultados dentro de límites aceptables. Sin embargo, estas mediciones pueden no ser concluyentes porque es posible que no cambien hasta que el aislamiento esté muy degradado. En comparación con la PF/DF a frecuencia de potencia, 1 Hz es hasta 10 veces más sensible a los cambios en el aislamiento y proporciona una confirmación inmediata de la degradación o contaminación del aislamiento.

¿También depende 1 Hz de la temperatura? ¿Es posible la corrección a 20 °C?

Absolutamente. La evaluación de PF/DF puede ser defectuosa sin una corrección adecuada de la temperatura. Sin embargo, las tablas de corrección de temperatura no se aplican a las mediciones de 1 Hz. Además, aunque se pudieran utilizar tablas de corrección de temperatura, la norma IEEE C57.12.90 establece que ninguna curva de corrección se ajustará a todos los casos. Para solucionar este problema, el DELTA4000 y el TRAX + TDX de Megger utilizan mediciones de PF/DF de 1 Hz a 505 Hz para proporcionar la Corrección Individual de Temperatura (ITC), corrección de temperatura basada en el estado real del aislamiento.

¿Necesito una conexión de prueba separada y/o un software diferente para las pruebas de 1 Hz y de ITC?

Las pruebas de 1 Hz e ITC utilizan la misma conexión que las pruebas de frecuencia de potencia de 10 kV.  El software está preconfigurado para ejecutar las pruebas y mostrar los resultados junto con los resultados de frecuencia de potencia.

¿Cómo contribuye el factor de potencia/disipación (PF/DF) de 1 Hz a la evaluación inmediata del aislamiento?

A frecuencias más bajas, aumenta la sensibilidad de los cambios dieléctricos debidos a la humedad o la contaminación. Esto significa que los valores de 1 Hz serán más altos y aumentarán antes que los valores de potencia de frecuencia de línea. Por lo tanto, la medición de la frecuencia de potencia y de 1 Hz corregida a 20 °C es una herramienta eficaz para identificar la degradación temprana y avanzada y el posible fallo del aislamiento de componentes de alta tensión, como transformadores y casquillos.

¿Qué instrumentos necesita para realizar pruebas a 1 Hz?

La medición del FP a 1 Hz puede realizarse con un instrumento DFR dedicado (serie IDAX 300), o con el mismo equipo utilizado para las pruebas de factor de potencia/factor de disipación a 10 kV (DELTA 4000 o TRAX + TDX).

¿Por qué las pruebas a 1 Hz suponen una gran diferencia?

1 Hz ist eine proaktive Methode zur Validierung der häufig verwendeten Netzfrequenz-PF/DF-Ergebnisse.

a. El desajuste en la evaluación de los resultados de frecuencia de potencia frente a 1 Hz corregidos correctamente a 20 °C mediante el algoritmo ITC es indicativo de una degradación progresiva del material aislante.
b. Proporciona confianza en la evaluación dieléctrica y eleva el funcionamiento seguro y fiable de los activos de AT.
c. Los gestores de activos y los especialistas en mantenimiento confían en los resultados fiables de las pruebas para garantizar la prolongación de la vida útil de los componentes críticos de la red eléctrica.

Pruebas de 1 Hz frente a pruebas de 50/60 Hz

Mueva el control deslizante inferior de izquierda a derecha para ver la diferencia entre la evaluación del estado dieléctrico de transformadores y casquillos a 50/60 Hz y el resultado más preciso de las pruebas a 1 Hz.

At 50 Hz or 60 Hz, increases in power factor / tan delta values are slow to develop.  The insulation may be changing, but the measured power factor / tan delta values do not.  A transformer in service for 50 years may measure nearly the same 50 Hz / 60 Hz power factor / tan delta values as it did when it was new...does that mean the insulation hasn't changed?

At 1 Hz, power factor / tan delta values react quickly to changes in insulation.  At 1 Hz, moisture in the paper and contamination in the liquid are amplified.  A transformer that has been in service for 50 years will show clear changes at 1 Hz, where 50  Hz or 60 Hz cannot.

50 Hz/60 Hz
1 Hz
50 Hz/60 Hz
  • Power factor tan delta values react slowly to changes in solid and liquid insulation
  • Effects of moisture in the paper and contamination in the insulating liquid are hidden
  • A transformer in service for 50 years may measure nearly the same power factor tan delta values as it did when it was new
1 Hz
  • Power factor tan delta values react quickly to changes in solid and liquid insulation.
  • Effects of moisture in the paper and contamination in the insulating liquid are amplified
  • A transformer in service for 50 years will show clear changes at 1 Hz, where 50 Hz or 60 Hz cannot
50 Hz /
60 Hz
  • Power factor tan delta values react slowly to changes in solid and liquid insulation
  • Effects of moisture in the paper and contamination in the insulating liquid are hidden
  • A transformer in service for 50 years may measure nearly the same power factor tan delta values as it did when it was new
1 Hz
  • Power factor tan delta values react quickly to changes in solid and liquid insulation
  • Effects of moisture in the paper and contamination in the insulating liquid are amplified
  • A transformer in service for 50 years will show clear changes at 1 Hz, where 50 Hz or 60 Hz cannot
Parameter
PF/DF at 50 or 60 Hz
PF/DF at 1 Hz

Voltage

1 V – 12 kV

1V – 250 V

Frequency range

45 – 65 Hz

1 – 505 Hz

Temperature correction

Average table correction factors

Individual Temperature Correction (ITC)

Testing time

~ 20 – 30 seconds

~ 5 – 6 minutes

Area of influence

Mainly solid insulation

Solid and liquid insulation

Trending

Best practice

Optional

Limits

Set by standards

Set by DFR assessment

Los productos que hacen posible las pruebas a 1 Hz

IDAX322
Insulation diagnostic analyser based on HV dielectric frequency response (DFR)
DELTA4000
12 kV insulation diagnostic system

TRAX+TDX
Multifunction transformer and substation test system

IDAX322

Analizador de diagnóstico de aislamiento basado en la respuesta en frecuencia dieléctrica (DFR) de AT

Learn more

DELTA4000

Sistema de diagnóstico de aislamiento de 12 kV

Learn more

TRAX+TDX

Sistema multifunción de ensayo de transformadores y subestaciones

Learn more

Who are you?

1 Hz is the technology capable to validate, line frequency power factor / tan delta tests. The objective is to extend the service life of  assets without depending of any trending or database and even more, avoiding any other additional investments, to know the real condition of the insulation of their assets.

Find personalized content for you

Digital Substation

Software, data communication and control, etc., is standard in modern substations. Though the development and implementation of IEC 61850 since mid 2000’s, the way to design, configure and run the substations have changed. This IT influence brings many advantages but also introduce new challenges to the industry.

Distributed energy resources

The power network is facing a huge change moving from centralized, large generation stations to smaller DER. Accurate communication leading to quick and correct decisions will be key in the development of the smart grid. The relay protection in DERs, like wind and solar farms, uses rather basic protection functions but their design creates other challenges when it comes to testing.

Special and advanced applications

Advanced relay testing refer to protection functions that isn’t straight forward parameters such as current, voltage or frequency. Even though that is exactly what is measured and calculated, the advanced protection category is either presented in another format, such as impedance for distance protection, or require complex test setup as transformer differential.

Webinars

Real time data tracking provides up-to-date visibility of your grid's performance

Learn More >

IEC 61850 Solutions

Fault detection, quick location, determination, and predictive maintenance tools decrease SAIDI and SAIFI

Learn More >

Latest Technical Content

Comprehensive data sets and analytics tools deliver the knowledge to make intelligent data-based decisions

Learn More >
Tab Content Title

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Suspendisse varius enim in eros elementum tristique. Duis cursus, mi quis viverra ornare, eros dolor interdum nulla, ut commodo diam libero vitae erat. Aenean faucibus nibh et justo cursus id rutrum lorem imperdiet. Nunc ut sem vitae risus tristique posuere.

Tab Content Title

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Suspendisse varius enim in eros elementum tristique. Duis cursus, mi quis viverra ornare, eros dolor interdum nulla, ut commodo diam libero vitae erat. Aenean faucibus nibh et justo cursus id rutrum lorem imperdiet. Nunc ut sem vitae risus tristique posuere.

Tab Content Title

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Suspendisse varius enim in eros elementum tristique. Duis cursus, mi quis viverra ornare, eros dolor interdum nulla, ut commodo diam libero vitae erat. Aenean faucibus nibh et justo cursus id rutrum lorem imperdiet. Nunc ut sem vitae risus tristique posuere.

Tab Content Title

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Suspendisse varius enim in eros elementum tristique. Duis cursus, mi quis viverra ornare, eros dolor interdum nulla, ut commodo diam libero vitae erat. Aenean faucibus nibh et justo cursus id rutrum lorem imperdiet. Nunc ut sem vitae risus tristique posuere.

Webinars

Please watch the latest webinars about 1 Hz here

View more

Case studies

Keep updated with the latest case studies about 1 Hz testing

View more

Technical Article

Learn more about 1 Hz with latest technical articles and news

View more

Videos

Watch the latest videos, interviews and podcasts

View more
Vídeos, entrevistas y podcasts
Información técnica actualizada
Webinars
A little touch-up animation for the paragraph that reveals on expand

To make things a little livelier, I added a nice little touch up to the paragraph by creating a slide in animation from below. So, instead of being still upon expand, it will slide in from below nicely.

Additional interaction to create focus/highlight on specific item (Optional)

I added a focus/highlight effect to make the item that's on hover stands out from the rest. This helps the user to focus on the item that they are reading.

This is definitely optional. You can remove this animation from the interaction setting. It's a separate interaction from the expand/collapse.

Contact

Thank you! Your submission has been received!
Oops! Something went wrong while submitting the form.