Relay protection testing solutions

The key partner to take assertive decisions over your protection network
See how it works
X
See how it works
Learn more

1 Hz testing.

One test makes a big difference

La prueba del factor de potencia/factor de disipación a 1 Hz proporciona confianza en la evaluación de la condición de aislamiento medido a 50/60 Hz.
Con un instrumento y una conexión, una prueba proporciona una toma de decisiones inmediata y confiable para activos críticos de alta tensión.

Bloque de preguntas y respuestas

Lorem ipsum dolor sit amet, consectetur adipiscing elit.

¿Tiene usted alguna duda sobre los resultados de la prueba del factor de potencia/factor de disipación (FP/FD) de sus activos de alta tensión obtenidos la frecuencia de red (50 o 60 Hz)

En el campo, es común medir FP/FD a la frecuencia de red y obtener resultados dentro de los límites aceptables. Sin embargo, estas mediciones pueden ser inconclusas, ya que es posible que no cambien hasta que el material aislante presente una degradación severa. En comparación con el FP/FD a frecuencia de red, la medición a 1 Hz es hasta 10 veces más sensible a los cambios del aislamiento y proporciona una confirmación inmediata de la degradación o la contaminación del material aislante.

¿Es 1 Hz también dependiente de la temperatura? ¿Es posible corregir a 20 °C?

La evaluación del FP/FD puede ser incorrecta sin una adecuada corrección de temperatura. Sin embargo, las tablas de corrección de temperatura no se aplican a las mediciones de 1 Hz. Además, incluso si se pudieran utilizar tablas de corrección de temperatura, la norma IEEE C57.12.90 indica que ninguna curva de corrección se ajustará a todos los casos. Para abordar esto, DELTA4000 y TRAX + TDX de Megger utilizan mediciones de FP/FD de 1 Hz a 505 Hz para proporcionar una corrección individual de temperatura (ITC, del inglés ‌‌Individual Temperature Correction‌‌), corrección de temperatura basada en la condición real del aislamiento.

¿Necesito una conexión de prueba distinta o un software diferente para las pruebas de 1 Hz e ITC?

No! 1 Hz and ITC tests use the same test connection as 10 kV power frequency tests.  The software is preconfigured to execute the tests and display results alongside the power frequency results.

¿De qué manera el factor de potencia/factor de disipación (FP/FD) a 1 Hz ayuda a la evaluación inmediata del material aislante?

A frecuencias más bajas, aumenta la sensibilidad de los cambios dieléctricos debido a la humedad o la contaminación. Esto significa que los valores a 1 Hz serán más altos y aumentarán antes que los valores a frecuencia de red. Por lo tanto, la medición a frecuencia de red y a 1 Hz corregida a 20 °C es una herramienta eficaz para identificar la degradación temprana y avanzada, y la posible falla del aislamiento de los componentes de alta tensión, tales como transformadores y bushings.

¿Qué instrumentos necesita para las pruebas de 1 Hz?

La medición de FP a 1 Hz se puede realizar con un instrumento DFR dedicado (serie IDAX 300) o con el mismo equipo utilizado para las pruebas de factor de potencia/factor de disipación de 10 kV (DELTA 4000 o TRAX + TDX).

¿Por qué la prueba a 1 Hz hace una gran diferencia?

1 Hz es una forma proactiva de validar los resultados de FP/FD a la frecuencia de red comúnmente utilizada.

a. El beneficio en la evaluación del factor de potencia (factor de disipación) a la frecuencia de red conjuntamente con los resultados medidos a 1 Hz correctamente corregidos a 20 °C, se debe a la alta sensibilidad de 1 Hz para detectar una degradación progresiva del material aislante y poder validar los resultados obtenidos a frecuencia de red (50 o 60 Hz).
b. Proporciona confianza en la evaluación dieléctrica y eleva la seguridad y confiabilidad en la operación de los activos de alta tensión.
c. Los administradores de activos y especialistas en mantenimiento dependen de resultados certeros y confiables de las pruebas eléctricas y dieléctricas. Con esto, pueden garantizar una vida útil prolongada de los componentes críticos dentro de la red eléctrica.

Prueba a 1 Hz en comparación con la prueba a 50/60 Hz

Mueva el control deslizante  de izquierda a derecha en la imagen abajo para ver la diferencia entre la evaluación de la condición dieléctrica de transformadores y bushings a 50/60 Hz y la prueba de resultados más precisa a 1 Hz.

At 50 Hz or 60 Hz, increases in power factor / tan delta values are slow to develop.  The insulation may be changing, but the measured power factor / tan delta values do not.  A transformer in service for 50 years may measure nearly the same 50 Hz / 60 Hz power factor / tan delta values as it did when it was new...does that mean the insulation hasn't changed?

At 1 Hz, power factor / tan delta values react quickly to changes in insulation.  At 1 Hz, moisture in the paper and contamination in the liquid are amplified.  A transformer that has been in service for 50 years will show clear changes at 1 Hz, where 50  Hz or 60 Hz cannot.

50 Hz/60 Hz
1 Hz
50 Hz/60 Hz
  • Power factor tan delta values react slowly to changes in solid and liquid insulation
  • Effects of moisture in the paper and contamination in the insulating liquid are hidden
  • A transformer in service for 50 years may measure nearly the same power factor tan delta values as it did when it was new
1 Hz
  • Power factor tan delta values react quickly to changes in solid and liquid insulation.
  • Effects of moisture in the paper and contamination in the insulating liquid are amplified
  • A transformer in service for 50 years will show clear changes at 1 Hz, where 50 Hz or 60 Hz cannot
50 Hz /
60 Hz
  • Power factor tan delta values react slowly to changes in solid and liquid insulation
  • Effects of moisture in the paper and contamination in the insulating liquid are hidden
  • A transformer in service for 50 years may measure nearly the same power factor tan delta values as it did when it was new
1 Hz
  • Power factor tan delta values react quickly to changes in solid and liquid insulation
  • Effects of moisture in the paper and contamination in the insulating liquid are amplified
  • A transformer in service for 50 years will show clear changes at 1 Hz, where 50 Hz or 60 Hz cannot
Parameter
PF/DF at 50 or 60 Hz
PF/DF at 1 Hz

Voltage

1 V – 12 kV

1V – 250 V

Frequency range

45 – 65 Hz

1 – 505 Hz

Temperature correction

Average table correction factors

Individual Temperature Correction (ITC)

Testing time

~ 20 – 30 seconds

~ 5 – 6 minutes

Area of influence

Mainly solid insulation

Solid and liquid insulation

Trending

Best practice

Optional

Limits

Set by standards

Set by DFR assessment

Los instrumentos que hacen posible la prueba a 1 Hz

IDAX322
Insulation diagnostic analyser based on HV dielectric frequency response (DFR)
DELTA4000
12 kV insulation diagnostic system

TRAX+TDX
Multifunction transformer and substation test system

IDAX322

Analizador de diagnóstico de aislamiento basado en respuesta de frecuencia dieléctrica (DFR) de alta tensión

Learn more

DELTA4000

Sistema de diagnóstico de aislamiento de 12 kV

Learn more

TRAX+TDX

Sistema multifuncional para prueba de transformadores y subestaciones

Learn more

Who are you?

1 Hz is the technology capable to validate, line frequency power factor / tan delta tests. The objective is to extend the service life of  assets without depending of any trending or database and even more, avoiding any other additional investments, to know the real condition of the insulation of their assets.

Find personalized content for you

Digital Substation

Software, data communication and control, etc., is standard in modern substations. Though the development and implementation of IEC 61850 since mid 2000’s, the way to design, configure and run the substations have changed. This IT influence brings many advantages but also introduce new challenges to the industry.

Distributed energy resources

The power network is facing a huge change moving from centralized, large generation stations to smaller DER. Accurate communication leading to quick and correct decisions will be key in the development of the smart grid. The relay protection in DERs, like wind and solar farms, uses rather basic protection functions but their design creates other challenges when it comes to testing.

Special and advanced applications

Advanced relay testing refer to protection functions that isn’t straight forward parameters such as current, voltage or frequency. Even though that is exactly what is measured and calculated, the advanced protection category is either presented in another format, such as impedance for distance protection, or require complex test setup as transformer differential.

Webinars

Real time data tracking provides up-to-date visibility of your grid's performance

Learn More >

IEC 61850 Solutions

Fault detection, quick location, determination, and predictive maintenance tools decrease SAIDI and SAIFI

Learn More >

Latest Technical Content

Comprehensive data sets and analytics tools deliver the knowledge to make intelligent data-based decisions

Learn More >
Tab Content Title

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Suspendisse varius enim in eros elementum tristique. Duis cursus, mi quis viverra ornare, eros dolor interdum nulla, ut commodo diam libero vitae erat. Aenean faucibus nibh et justo cursus id rutrum lorem imperdiet. Nunc ut sem vitae risus tristique posuere.

Tab Content Title

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Suspendisse varius enim in eros elementum tristique. Duis cursus, mi quis viverra ornare, eros dolor interdum nulla, ut commodo diam libero vitae erat. Aenean faucibus nibh et justo cursus id rutrum lorem imperdiet. Nunc ut sem vitae risus tristique posuere.

Tab Content Title

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Suspendisse varius enim in eros elementum tristique. Duis cursus, mi quis viverra ornare, eros dolor interdum nulla, ut commodo diam libero vitae erat. Aenean faucibus nibh et justo cursus id rutrum lorem imperdiet. Nunc ut sem vitae risus tristique posuere.

Tab Content Title

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Suspendisse varius enim in eros elementum tristique. Duis cursus, mi quis viverra ornare, eros dolor interdum nulla, ut commodo diam libero vitae erat. Aenean faucibus nibh et justo cursus id rutrum lorem imperdiet. Nunc ut sem vitae risus tristique posuere.

Webinars

Please watch the latest webinars about 1 Hz here

View more

Case studies

Keep updated with the latest case studies about 1 Hz testing

View more

Technical Article

Learn more about 1 Hz with latest technical articles and news

View more

Videos

Watch the latest videos, interviews and podcasts

View more
Medios
Información técnica
Webinars
A little touch-up animation for the paragraph that reveals on expand

To make things a little livelier, I added a nice little touch up to the paragraph by creating a slide in animation from below. So, instead of being still upon expand, it will slide in from below nicely.

Additional interaction to create focus/highlight on specific item (Optional)

I added a focus/highlight effect to make the item that's on hover stands out from the rest. This helps the user to focus on the item that they are reading.

This is definitely optional. You can remove this animation from the interaction setting. It's a separate interaction from the expand/collapse.

Contact

Thank you! Your submission has been received!
Oops! Something went wrong while submitting the form.